QMobile S1 Firmware

How to Flash QMobile S1  Free With SP Flash Tool?

  • First download firmware for you cellphone and extract it using any unzip utility.
  • Install required MTK USB drivers.
  • Open SP Flash Tool v5.1612 available in firmware package or download from given link.
  • Press Scatter-loading button and go to firmware folder select MT65xx_Android_scatter.txt
  • Press Download button and wait let sp flash tool to test firmware files that are going to be flashed when finish file checking immediately connect powered off  mobile phone to USB cable.
  • Let Sp Flash Tool finish the job it will take few minutes.
  • Download OK message will be appear on screen with big green [O]
  • Disconnect phone from USB cable after appearing of Download OK message with big green [O]
  • Power on your mobile phone and wait few minutes to complete boot process first time.
  • Then configure phone with your required setting and done!

Please visit How to Flash MTK Smart Phones With SP Flash Tool for video tutorial and screenshots flashing with sp flash tool.

 

QMobile S1 Firmware:

QMobile S1 Firmware Free Download

 

QMobile S1 Firmware Flashing Done With CM2 Dongle:

Chinese Miracle II [MTK module] v 1.56


Scatter Load Ok , BaseBand : MT6582 , Project : s5222 , Storage : EMMC
 Files found : 11 , Set to Flash : 10
 Ready to Flash!

Operation : Flash [ v1.56 ]

======= Flash
 1. Power Off Phone , Remove battery , Insert back
 2. Insert USB cable. In some cases require hold BootKey

Wait for phone...
 Phone found! [ 19 ]
 Sync...
 Inital Boot Ok!
 BB_CPU_PID : 6582
 BB_CPU_NME : [MediaTek] MT6582_S00
 BB_CPU_EXT : 0xCB00 , 0x8A00 , 0x0000
 Processing BROM stage
 Settings for BROM configured!
 SecCfgVal : 0x00000000
 BromVer : 0x00FF
 BLVersion : 0x0001
 PreLoader : Active [ Boot with PL ]
 BootLdrSS : NORMAL with PRELOADER
 Processing DA stage
 DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
 Sending and initialize DA ...
 Running DA ver.4.2 on BBID : 0x87
 NAND Flash : NOT INSTALLED
 eMMC Flash : 90014A4838473165050733B7991492C9
 Initialize Memory ...
 DRAM already initialized by Preloader
 DAgent sent , init HW now
 eMMC FlashIC initialized
 [eMMC] : FLASH_VEN : 0x90 , OEM : 014A
 [eMMC] : FLASH_INF : [HYNIX] , e1G8
 [eMMC] : FLASH_CID : 90014A4838473165050733B7991492C9
 [eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
 [eMMC] : FLASH_LEN : 0x00000001D2000000
 [eMMC] : FLASH_UCP : 7456 MiB [eMMC 8 GiB]
 DEV RID : 0x4B87B7682CA66847157DA714184590A7
 INT RAM : 0x00020000
 EXT RAM : 0x40000000 [1 GiB]
 BOOT TYPE : EMMC_FLASH_BOOT
 SOC VERIFY : C1
 Boot Ok!

ScatCFG : BaseBand : MT6582 , Project : s5222 , Storage : EMMC
 Setting : Flash Pre-Erase (Safe) : Enabled
 Setting : AFF verify : Enabled
 Setting : HW verify : Enabled

BL : Check HW compatibility
 BL : BBID supported by BootLoader!
 BL : Check eMMC compatibility
 BL : eMMC supported by BootLoader!

BL : BatteryLevel : 3498 mV
 BL : [WARNING] : BatteryLevel LOW!!!

BL : Flash Pre-Erase
 Total blocks to Erase : 2
 Erase : 0x0000000000C00000-0x0000000000100000
 Erase : 0x0000000002900000-0x00000001CEE00000
 Flash Pre-Erase Done, time used : 00:00:02

SecCfg Passed , 1799
 BMT remark not need. Will skip
 Sending Preloader ...
 Use : preloader_s5222.bin
 Preloader Sent , Init passed
 SecCfg Passed , 1799
 PartCount : 0012
 Update PMT by user request
 Repartition Done!
 Use FLN Mode

Processing : Flash Write
 Flash now : MBR
 Image Flash Ok
 Flash now : EBR1
 Image Flash Ok
 Flash now : UBOOT
 Image Flash Ok
 Flash now : BOOTIMG
 Image Flash Ok
 Flash now : RECOVERY
 Image Flash Ok
 Flash now : SEC_RO
 Image Flash Ok
 Flash now : LOGO
 Image Flash Ok
 Flash now : ANDROID
 Image Flash Ok
 Flash now : CACHE
 Image Flash Ok
 Flash now : USRDATA
 Image Flash Ok
 Flash Write Done, time used : 00:03:31

Processing : Verify
 Verify Passed : MBR
 Verify Passed : EBR1
 Verify Passed : UBOOT
 Verify Passed : BOOTIMG
 Verify Passed : RECOVERY
 Verify Passed : SEC_RO
 Verify Passed : LOGO
 Verify Passed : ANDROID
 Verify Passed : CACHE
 Verify Passed : USRDATA
 Data Verify Done, time used : 00:01:55

Update Mirror PMT
 Update Done!

Update RomInfo done

Done!
 Elapsed: 00:05:42
 Reconnect Power/Cable!

Leave a Comment

%d bloggers like this: